Install Serial

Explanation

This activity is used to install a serial into a serial structure. Before a serial can be installed in a serial structure, observe the following guidelines for a more accurate installation of the serial.

• A serial with an operational status of Planned for Operation can only be installed in a serial with the same operational status.
• A serial with an operational status of In Operation or Out Of Operation can be installed in a serial with the following statuses: Planned For Operation, In Operation and Out Of Operation.
• A serial with operational status Scrapped or Renamed cannot be installed in another serial.
• The serial to install cannot be locked.
• A serial can only be installed in a serial structure whose configuration (serial structure template) allows it to be installed. This means that a part number or revision combination not existing (as prime part or alternate) in a level in the serial structure template cannot be installed in this level in the serial structure, and vice versa. For more information, refer the activity Define Template Part.
• The quantity of a certain part number or revision combination in the serial structure cannot exceed the number in the serial structure template.
• Alternate parts can be used in the serial structure as long as it has been defined either as a template alternate or a position alternate in the serial structure template. For more information, refer the activities Define Alternate Parts per Position and Define Alternate Parts in Template.
• When installing serials to a structure position, you are allowed to install any prime parts or valid alternates, provided that the operational status of the structure was not changed from Planned For Operation. Once the operational status of the structure is changed from Planned For Operation, rules of interchangeability will be applied and you will no longer be allowed to install alternate parts that do not meet the validations for interchangeability of alternate parts. Note that it is also possible to install any prime parts or alternates for structure positions in completely new structures which are In Operation or Out Of Operation, but where no parts are installed after a structure change was performed.
• If the life limited setting of the serial is Life Limited it can only be installed into a structure position defined as Life Limited. If the life limited setting of the serial is Not Life Limited it can only be installed into a structure position defined as Not Life Limited.

When a serial is installed in the structure, the current location will be cleared because the serial will be located at the same location as the top serial in the structure. If the serial to be installed exists in another structure or does not exist at all, a structure mismatch log entry will be created in the Serial Structure Mismatch Log window. A structure mismatch log will be created if a structure change is done in IFS/Work Order Management or IFS/Shop Order.

If access control is established, you can use only the serials to which you have access. Establishing access control is done by assigning a user to an access group defined in basic data. The access groups will be used to extend access to all or selected parts and serials in a structure. When a serial is installed in an existing structure position of the serial structure, it will receive the access rights from the parent serial in the structure. The serials below in the structure will also be updated with these access rights.

Prerequisites

• A structure position not occupied by the other parts or serials must exist in the selected structure before a serial can be installed.
• You must have access to the relevant serials to be able to carry out a structure change.

System Effects

• You will fit selected serial to a predefined serial structure position and create a historical record of the structure change.
• The structure position into which the serial is installed will become an installed structure position.
• If the installation causes a Mandatory type dependency rule to be violated, the operational condition of the parent serial will be set to Non Operational.
• The Item Installed check box will be selected for the installed serial.
• If the serial installed is defined as an alternate with the interchangeability rule Qualified Interchangeable, the alternate must be approved before the operational condition for the structure can be set to Operational. For more information, refer the activity Approve or Reject Structure Changes.
• After a serial has been installed into a serial structure the first time, and the life limited setting of the serial is not yet decided (the Life Limited field have the value "-"), the value of the Life Limited field will be set to Life Limited or Not Life Limited depending on the structure position it was installed into.
• If the structure change is performed from a work order, a mismatch record will be created if the installed serial is installed in another serial or does not exist.
• When the serial is installed in a structure, the serial will receive access rights from the parent serial of the selected structure.

Window

Serial Structure Information 
Report In Work Order
Work Task
Flight Log  

Related Window Descriptions

Structure Changes/Install Serial
Structure Changes - Select Action 
Serial Structure Information    
Serial Structure Information/Consist Of
Report In Work Order/Work Tasks/Task Card
Work Task/Task Card
Flight Log/Fault  

Procedure

Use this procedure to install a serial into a serial structure:

1. Open the Serial Structure Information window and query (F3) for the necessary structure.
2. In the graphical object structure, select the empty structure position into which the serial is to be installed, right-click, point to Structure Changes, and then click Install Serial. The Install Serial assistant opens.

Note: This assistant can also be opened from the Consist Of tab, by right-clicking on a serial record, pointing to Structure Changes, and then clicking Install Serial. When you are working in this tab, and need to move down the structure, select the required serial record, right-click and then click Next Level until the required structure level is displayed.

3. The vehicle ID, top part number and top serial number appear automatically in the Install or Swap into area.
4. In the Structure Position field, enter the structure position in which the serial is to be installed. A structure position must exist for a serial to be installed in the structure. Click List to select a structure position currently unoccupied.
5. Enter a value in the Part No/Rev field. Click List to select a valid value. When a value is entered in this field, the values for Serial Number and Inst. Date appear automatically.
6. In the Workshop field, enter the workshop responsible for installing the serial. Click List to select a valid value.
7. If you want to connect the serial installation to a maintenance event, click List to select a valid value for the Mx Event Number field.
8. In the Str. Change Date field, enter the date and time the structure change is to be performed.
9. Select the Unscheduled Removal? check box if this structure change is to be an unscheduled removal.
10. Select the Run in Batch? check box if you want access rights for the installed serial to be updated through a batch job.
11. Click Finish to close the assistant and perform the structure change.

Use this procedure to perform a structure change, i.e., install a serial, for the structure of the serial on the work task:

1. Open the Report In Work Order window and query (F3) for the desired work order.
2. Click the Work Tasks tab, select the desired task, and then click the Task Card tab. Alternatively, the Work Task/Task Card tab can be used to perform these steps.
3. Right-click and click Perform Structure Change. The Structure Changes - Select Action assistant step opens.
4. Select Install Serial and then click Next. The Install Serial step opens.
5. The vehicle ID, top part number and top serial number appear automatically in the Install or Swap into area.
6. In the Structure Position field, enter the structure position in which the serial is to be installed. A structure position must exist for a serial to be installed in the structure. Click List to select a structure position currently unoccupied.
7. Enter a value in the Part No/Rev field. Click List to select a valid value. When a value is entered in this field, the values for Serial Number and Inst. Date appear automatically.
8. The workshop to which the work order was distributed appears automatically in the Workshop field. If necessary, you can change to another workshop using the List of Values.
9. In the Str. Change Date field, enter the correct date and time the structure change is to be performed.
10. Click Finish to close the assistant and perform the structure change.

Use this procedure to perform a structure change, i.e., install a serial in the structure of the vehicle on which the fault was reported:

1. Open the Flight Log window and populate (F2) or query (F3) for your flight log number and/or serial.
2. Click the Fault tab and select the relevant fault number from the Fault Number list.
3. Right-click and click Perform Structure Change. The Structure Changes - Select Action step opens.
4. Verify that the Install Serial option is selected and then click Next. The Install Serial step opens.
5. Continue with steps 3 to 11 described in the first procedure listed above.